1產品圖片Product Image
2產品介紹Products Introduction
三樂硅酸鈣板的原材料由高純度石英粉，高標號水泥，高純度消石灰，加上石棉纖維及其他礦物添加物質組成，制作出來的硅酸鈣板高韌性，高強度，高防水，堅固耐用。原材料按硅鈣配比攪拌混合后，經抄取設備抄取制胚，其后一天的高壓蒸養使其硅鈣反應成“托貝莫來石”而硬化。從原材料處理到正壓后板成品加工，每一道工序均嚴格控制，保證市場提供品質穩定優良的通用硅酸鈣板材。
The raw mater ial of Sanle calcium silicate board are high-purity quartz flour,high grade Portland cement, high-purity slaked lime,plant fiber and other mineral added substance.After agitating and mixing calcium and silicate at a ratio,we make the raw material into a wet sheet and then through one day high temperature autoclave by advanced technology to make the calcium silicate react to Tobermorite to have the final product.From handling the raw material to processing semi-finished product,every procedure is under strict control to guarantee that supplying high quality calcium silicate board.

3產品特點Product Features
　　纖維增強硅酸鈣板屬于輕質高強建筑材料，施工方便，加工性能好，可鋸，可釘，不易產生翹曲和裂縫，表面可涂刷涂料或粘貼壁紙和瓷磚，并且不怕蟲蛀，不會發熱，其隔熱，隔聲性能，對溫度變化的穩定性均可滿足建筑物的使用要求。特別是具有良好的防火性能，不會爆裂，當發生火災時有較長時間安全撤離火災區。
總體來說：三樂硅酸鈣板 輕質高強 堅固耐用 隔聲隔熱 防蛀防腐 可刻可鋸可鉆 易施工 易裝飾 變形系數小
Fire proof
Sanle calcium silicate board is fire resistance material.When fire happens,not only the place occurs the fire,but also the place fire spreads to will be damaged and will bring loss,therefore,the fire resistance of outer wall is very important.Sanle calcium silicate board is with excellent fire resistance character.In addition,it will be not causing crack and stratification after fire.
Anticorrosive
Sanle calcium silicate board is without any growth condition for fungus,and it will not be mildew in any circumstance.
Resistant to insect and termite
Under 11pa steam curing,the Sanle calcium silicate board is hardening.Its own structural property decides that the insect and termite can not survive in the board.
Light weight & high strength
The wall,hang ceiling or other structural parts,which is fast.It is can be installed with ordinary wood working tool.The board is easy to be processed.
Easy working
The instanllation of board is dry construction, which is fast. It is can be installed with ordinary wood working tool.The board is easy to be processed.
Easy decoration
Various decorative processing can be made for the board surface,such as coating materials or all kinds of adhesive.
Small deformation coefficient
The materials of Sanle calcium silicate board are cement,quartz flour, natural xylem fiber and other minerals. Under high temperature autoclave, the calcium from the cement and the silicate from the quartz flour will react to form a new crystal "tobermorite".It will harden within 24 hours after molding, therefore the shape of board is steady and deformation coefficient is small.
4產品規格Product Specifications
5技術參數Product parameter
注： （表格中e是厚度） 如需查看檢測報告正本掃描檔案，請聯系我公司人員獲取！
6應用范圍Main functions
三樂硅酸鈣板可用于內外墻，吊頂，活動地板，廚廁墻板，輪船和地鐵工程板材，高層建筑上下水通道隔板，也可以作家具襯板，防火襯板，廣告牌，物柜板。
7建議使用場所Recommendable applications
商用建筑：商務大廈、娛樂場所、商場、酒店
工業建筑：工廠、倉庫
住宅建筑：新型住宅、裝修翻新
公共場所：醫院、劇院、車站
8搬運加工安裝指引Transportation cutting installation lead
運輸與搬運
工廠交貨時的三樂硅酸鈣板板材是采用板對板的堆垛儲存方式。這種狀態也適合海運，鐵路運輸，公路運輸和室內儲存。
三樂硅酸鈣板板材在存儲狀態中不適合置于室外或者有可能令產品接觸水的倉庫。三樂硅酸鈣板板材必須存儲于堅實，平整的地面，無漏水的，無塵通風的室內倉庫中。應避免在存儲狀態中受潮，萬一發生受潮，應立即抹干三樂硅酸鈣板板材并置于通風良好的地方晾干。否則，板材可能收到損壞。搬運時注意要項：
1.禁止單人搬運，注意邊角保護；
2.需要兩名工人在寬度方向一起將三樂硅酸鈣板抬起，雙手盡量分開，托起板的長邊，直立進行搬運，防止板材過度彎曲；
3.厚度不到8mm的板材在搬運時，建議每次兩片重疊搬運；
4.存放時，保證底部平整，每垛高度≤800mm，儲放垛數不超過三垛；
5.不能零散直立放置板材，應按規格、種類整齊平疊堆放；
6.儲放處必須干燥，無漏水，滲水現象，保證板材的優越性能。
加工方法
手工切割三樂硅酸鈣板材，可用一般的薄片鋸或手鋸完成。如大量板材需要現場切割時，建議使用電動圓盤齒鋸。切割鋸片是直齒的碳化鎢合金制成。對圓形或弧形的切割可采用電動曲線鋸進行施工。
可用電鉆或開孔器在板面上鉆圓孔或開方孔。
切割地點建議選在具有良好通風效果的地方。選用帶收塵設備的切割器，工人應佩帶口罩，以保護環境及員工的健康。
隔墻安裝
1.通常情況下，作隔墻的三樂硅酸鈣板采用縱向排布，即板的長邊落在豎龍骨上；
2.三樂硅酸鈣板對接時要自然靠近，不得強壓就位；
3.特別注意門窗處三樂硅酸鈣板的排放，注意板縫不能落在平行于門邊框，或窗邊框的龍骨上，以避免由于門窗的經常開關產生震動而造成三樂硅酸鈣板縫開裂；
4.三樂硅酸鈣板的兩條長邊都已倒角，如果墻體高于2440mm時，三樂硅酸鈣板水平接合的短邊必須現場倒角（刨成寬度約25mm的斜邊），以便更好的處理接縫。
5.彈線并標注板的固定點，同時作鉆孔處理（孔徑比螺釘頭略大1-2mm，孔深1-2mm）固定點距板角40-55mm，固定點間距250-300mm。
6.固定三樂硅酸鈣板時，板與龍骨應做與鉆孔，其孔徑應比螺絲直徑小1mm，用自攻釘固定時，應從板的中部向周邊固定，且所有螺釘頭均沉入板面1mm。在緊固時，板材必須與龍骨架釘牢。
Transportation
When delivery, the boards should be piled up in the way of board-to-board, then it is suitable for overseas transportation, road transportation and indoor store.
The panels could not be stored outside or in the store near water. It must be stored in a smooth, no rain leaking, no dust and good ventilated warehouse. It should avoid moisture before used.Once it was affected with damp, it should be cleaned up right away and sent it to a well ventilate area for drying up. Otherwise it may be destroyed.
Caution for transportation and store:
1.Carried by one man is prohibited, the edges and comers must be well protected.
2.Two workers are needed to lift the board together.They must separate their hands as much as possible and raise the length edges of the board in vertical so as to prevent the board from being bent too much.
3.Once the thickness of the board is less than 8mm, please carry two boards each time.
4.When storing, the bottom should be kept flat, the height of each stack should be not more than 800mm, and the total amount of storing should be not more than three.
5.The calcium silicate board can not be erectly scattered, on the contrary, the boards should be piled in order and according to their specification and type.
6.A dry depositary without water leakage and sink store must be chosen to ensure outstanding capabilities of Sanle calcium silicate board.
Cutting
Board can be cut manually with common flaky saws or handsaws.If a large amount of boards should be cut at the working site electric circular saws are suggested.The cutting saw blade is made of carbonized tungalloy. Moreover, cutting round and arc-shaped boards can be done with electric curvilinear saws.
Electric drills or tapers can be used for circular or rectangular holes as needed on the board surface.
Breezy spot is suggested as the site for cutting. In addition, cutters with the fuction of dust collection should be used, workers should wear respirators during processing, then the environment and health of the employees can be guaranteed.
Guide of installation and application for partition:
1.Generally, Sanle calcium silicate board which is used for partition is installed in vertiacal. That is to say, the length edge should be installed on the C Profile.
2.The panels are supposed to be approached naturally when they ard joined and forcible press should be avoided.
3.We have to pay special attention to the arrangement of panels near the windows and doors. The space of the panels should not be horizontal with the profile on frame of doors or windows in order to avoid the crack while shaking caused by opening or closing.
4.The two length edges of each panel are beveled edge. If the partition is higher than 2440mm, the shorter edge should be jointed horizontally on the spot(the bevel edges should be about 25mm in width)to make better sealing.
5.Snapping lines and marking fixed points for the panels, afterwards making a hole in advance(1-2mm in diameter, slightly bigger than screw head, and 1-2mm in depth). The fixed point should be 40-55mm to the corner of the board and the space between the fixed points should be 250-300mm.
6.Before the panels are fixed, it should be holed in advance on both the board and the profile. The size of the hole should be fixed from its center to edges, each screw should be enter into the board by 1mm. When fixing, please tight the panels and profile.
Guide of profile installation for ceiling
1.First, we should draw the installation guideline to confirm the fixing position according to the draft and the indoor condition (the distance between the fixing points is ≤1222mm).
2.Fixing the main profile on the bottom of the floor horizontally with hanging wire and hanger, the central distance between the main profiles is ≤1222mm, while the space between the end of the profile and the partition should be 10mm.
9備注Remark
如客戶需其他幅面尺寸，企業可代為切割；特殊規格可以預定加工。
10工程圖片Project picture
聯系人：一三四六三四三零六六六