压在透明的玻璃上c_又色又爽又黄又免费的视频软件_av无码专区亚洲av波多野结衣_国产在线每日都有更新 - www国产视频

阻燃防火材料-網上貿易平臺 | | WAP瀏覽
服務熱線:4006555305

ASTM D178橡膠絕緣墊子標準規范

放大字體  縮小字體 發布日期:2012-02-08   瀏覽次數:308  分享到: 分享到騰訊微博
ASTM D178橡膠絕緣墊子標準規范
ASTM D178 Standard Specification for Rubber Insulating Matting
ASTM D178橡膠絕緣墊子標準規范
X1.3.1 Tests made on a cellular plastic under conditions herein prescribed can be of considerable value in comparing the rate of burning and/or extent and time of burning of different materials, in controlling manufacturing processes, or as a measure of deterioration or change in burning characteristics prior to or during use.
X1.3.2 This test method is not intended to be a criterion for fire hazard. The fire hazard created by materials depends upon the form and end use of the material. Assessment of fire hazard includes, but is not limited to, many factors, such as, ease of ignition, burning rate, flame spread, fuel contribution, intensity of burning, and products of combustion.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers acceptance testing of rubber insulating matting for use as a floor covering for protection of workers.
1.2 Two types of matting, differing in chemical and physical characteristics, are provided and are designated as Type I and Type II matting.
1.3 The following safety hazards caveat applies only to the test method portion, Sections 17 to 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—Rubber insulating matting should remain flexible for use through normal temperature ranges.
Note 2—Rubber as used in this specification is a generic term that includes elastomers and elastomer compounds, regardless of origin.
X1.1.1 This test method covers a small-scale horizontal laboratory screening procedure for measuring the rate, extent, or time, or a combination thereof, of burning of rigid or flexible cellular plastics in accordance with this test procedure.
X1.1.2 Materials that exhibit pronounced shrinking, curling, or melting away upon heating cannot be evaluated by this test method.
X1.1.3 This test method is not applicable to materials that cannot be ignited under the conditions of this test, or to materials that exhibit progressive combustion without flame (continued glowing or charring).
Note X1.1—The rate of burning or extent of burning of rigid cellular plastics also may be determined by Test Method D3014 where the specimen is supported vertically.
X1.1.3.1 WarningDuring the course of combustion, gases or vapors, are evolved that may be hazardous to personnel. Adequate precautions should be taken to protect the operator.
X1.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
 
2. Referenced Documents (purchase separately)
ASTM Standards
D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
D297 Test Methods for Rubber Products--Chemical Analysis
D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers--Tension
D471 Test Method for Rubber Property--Effect of Liquids
D518 Test Method for Rubber Deterioration--Surface Cracking
D570 Test Method for Water Absorption of Plastics
D573 Test Method for Rubber--Deterioration in an Air Oven
D1564 Discontinued 1979; Testing Flexible Cellular Materials--Slab Urethane Foam; Replaced by D 3574
D1565 Specification for Flexible Cellular Materials--Vinyl Chloride Polymers and Copolymers (Open-Cell Foam)3
D1692 Discontinued 1978; Method of Test for Rate of Burning or Extent and Time of Burning of Cellular Plastics Using a Specimen Supported by a Horizontal Screen
D2406 Discontinued 1980; Methods of Testing Flexible Cellular Materials-Molded Urethane Foam; Replaced by D 3574
D3014 Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position
American National Standard
ANSIC84.1 Voltage Ratings for Electric Power Systems and Equipment (60 Hz)
Index Terms
rubber insulating matting;
 
 
 

  詳情請咨詢
  防火資源網-阻燃防火測試中心
  電話:(+86)0592-5056213
  傳真:(+86)0592-5105807
  郵件:firetest@firetc.com

凡注明"防火資源網"的所有作品,由<防火資源網>整理編輯,任何組織未經<防火資源網>及其擁有者授權,不得復制、轉載、摘編或利用其它方式應用于任何商業行為。

 
 
[ 防火測試中心搜索 ]  [ ]  [ 告訴好友 ]  [ 打印本文 ]  [ 關閉窗口 ]  [ 返回頂部 ]

 

 
 
推薦防火測試
推薦圖文
點擊排行
 
 
網站首頁 | 廣告服務 | 關于我們 | 聯系方式 | 服務協議 | 版權聲明 | 網站地圖 | 友情鏈接 | 網站留言 | 舊版本 | 閩ICP備09009213號
?2019-2021 FIRETC.COM All Rights Reserved ? 備案號:閩ICP備09009213號-1在線客服 點擊QQ交談/留言 點擊QQ交談/留言