ASTM E2019 Standard Test Method for Minimum Ignition Energy of a Dust Cloud in Air
ASTM E2019空氣中塵霧最小點火能量的標準試驗方法
This test method provides a procedure for performing laboratory tests to determine the minimum ignition energy of a dust cloud.
Note 1—For gases and vapors, see Test Method E 582.
The data developed by this test method may be used to assess the spark ignitibility of a dust cloud. Additional guidance on the significance of minimum ignition energy is in X1.1.
The values obtained are specific to the sample tested, the method used and the test equipment used. The values are not to be considered intrinsic material constants.
The MIE of a dust as determined using this procedure can be compared with the MIE's of reference dusts (using the same procedure) to obtain the relative sensitivity of the dust to spark ignition. An understanding of the relative sensitivity to spark ignition can be used to minimize the probability of explosions due to spark ignition.
1. Scope
1.1 This test method determines the minimum ignition energy of a dust cloud in air by a high voltage spark.
1.2 The Minimum Ignition Energy (MIE) of a dust-cloud is primarily used to assess the likelihood of ignition during processing and handling. The likelihood of ignition is used to evaluate the need for precautions such as explosion prevention systems. The MIE is determined as the electrical energy stored in a capacitor which, when released as a high voltage spark, is just sufficient to ignite the dust cloud at its most easily ignitable concentration in air. The laboratory test method described in this standard does not optimize all test variables that affect MIE. Smaller MIE values might be determined by increasing the number of repetitions or optimizing the spark discharge circuit for each dust tested.
1.3 In this test method, the test equipment is calibrated using a series of reference dusts whose MIE values lie within established limits. Once the test equipment is calibrated, the relative ignition sensitivity of other dusts can be found by comparing their MIE values with those of the reference dusts or with dusts whose ignition sensitivities are known from experience. X1.1 of this test method includes guidance on the significance of minimum ignition energy with respect to electrostatic discharges.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 8
2. Referenced Documents (purchase separately)
ASTM Standards
D3173 Test Method for Moisture in the Analysis Sample of Coal and Coke
D3175 Test Method for Volatile Matter in the Analysis Sample of Coal and Coke
E582 Test Method for Minimum Ignition Energy and Quenching Distance in Gaseous Mixtures
E789 Test Method for Dust Explosions in a 1.2-Litre Closed Cylindrical Vessel
E1226 Test Method for Pressure and Rate of Pressure Rise for Combustible Dusts
E1445 Terminology Relating to Hazard Potential of Chemicals
IEC Standards
1241-2-3,1994 Electrical Apparatus for Use in the Presence of Combustible Dusts, Part 2: Test Method, Section 3: Method for Determining Minimum Ignition Energy of Dust-Air Mixtures
Index Terms
dust; minimum ignition energy; spark ignition; Calibration--air/atmospheric analysis instruments; Calibration/standardization; Dust clouds; Dust ignition/explosion; Electric discharge; Ignition; Minimum ignition energy (MIE); Spark ignition;
ASTM E2019空氣中塵霧最小點火能量的標準試驗方法
This test method provides a procedure for performing laboratory tests to determine the minimum ignition energy of a dust cloud.
Note 1—For gases and vapors, see Test Method E 582.
The data developed by this test method may be used to assess the spark ignitibility of a dust cloud. Additional guidance on the significance of minimum ignition energy is in X1.1.
The values obtained are specific to the sample tested, the method used and the test equipment used. The values are not to be considered intrinsic material constants.
The MIE of a dust as determined using this procedure can be compared with the MIE's of reference dusts (using the same procedure) to obtain the relative sensitivity of the dust to spark ignition. An understanding of the relative sensitivity to spark ignition can be used to minimize the probability of explosions due to spark ignition.
1. Scope
1.1 This test method determines the minimum ignition energy of a dust cloud in air by a high voltage spark.
1.2 The Minimum Ignition Energy (MIE) of a dust-cloud is primarily used to assess the likelihood of ignition during processing and handling. The likelihood of ignition is used to evaluate the need for precautions such as explosion prevention systems. The MIE is determined as the electrical energy stored in a capacitor which, when released as a high voltage spark, is just sufficient to ignite the dust cloud at its most easily ignitable concentration in air. The laboratory test method described in this standard does not optimize all test variables that affect MIE. Smaller MIE values might be determined by increasing the number of repetitions or optimizing the spark discharge circuit for each dust tested.
1.3 In this test method, the test equipment is calibrated using a series of reference dusts whose MIE values lie within established limits. Once the test equipment is calibrated, the relative ignition sensitivity of other dusts can be found by comparing their MIE values with those of the reference dusts or with dusts whose ignition sensitivities are known from experience. X1.1 of this test method includes guidance on the significance of minimum ignition energy with respect to electrostatic discharges.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 8
2. Referenced Documents (purchase separately)
ASTM Standards
D3173 Test Method for Moisture in the Analysis Sample of Coal and Coke
D3175 Test Method for Volatile Matter in the Analysis Sample of Coal and Coke
E582 Test Method for Minimum Ignition Energy and Quenching Distance in Gaseous Mixtures
E789 Test Method for Dust Explosions in a 1.2-Litre Closed Cylindrical Vessel
E1226 Test Method for Pressure and Rate of Pressure Rise for Combustible Dusts
E1445 Terminology Relating to Hazard Potential of Chemicals
IEC Standards
1241-2-3,1994 Electrical Apparatus for Use in the Presence of Combustible Dusts, Part 2: Test Method, Section 3: Method for Determining Minimum Ignition Energy of Dust-Air Mixtures
Index Terms
dust; minimum ignition energy; spark ignition; Calibration--air/atmospheric analysis instruments; Calibration/standardization; Dust clouds; Dust ignition/explosion; Electric discharge; Ignition; Minimum ignition energy (MIE); Spark ignition;