ASTM E2187 Standard Test Method for Measuring the Ignition Strength of Cigarettes
ASTM E2187卷煙點燃強度測量的標準試驗方法
The most common initiating event in a fatal fire is the dropping of a cigarette onto a bed or piece of upholstered furniture, causing 20 % of the estimated U.S. fire deaths from 1992–1996 in residential structures, according to statistics provided by the U.S. Consumer Product Safety Commission. Test Methods E1352 and E1353 have been developed to evaluate the susceptibility of upholstered furniture mock-ups and components to ignition by cigarettes. Federal Standard 16 CFR Part 1632, Standard for the Flammability of Mattresses and Mattress Pads, was promulgated to reduce the likelihood that mattresses and mattress pads would ignite from a lighted cigarette.
This test method enables comparison of the relative ignition strength of different cigarette designs.
In this procedure, the specimens are subjected to a set of laboratory conditions. If different conditions are substituted or the end use conditions are changed, it may not be possible, using this test, to predict quantitative changes in the fire test response characteristics measured. Therefore, the quantitative results are valid only for the fire test exposure conditions described in this procedure.
1. Scope
1.1 This fire-test-response standard provides a standard measure of the capability of a cigarette, positioned on one of three standard substrates, to generate sufficient heat to continue burning and thus potentially cause ignition of bedding or upholstered furniture.
1.2 This method has value as a predictor of the relative propensity of a cigarette to ignite upholstered furnishings.
1.3 This method is applicable to cigarettes that burn along the length of a tobacco column.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.
2. Referenced Documents (purchase separately)
ASTM Standards
E176 Terminology of Fire Standards
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
E1352 Test Method for Cigarette Ignition Resistance of Mock-Up Upholstered Furniture Assemblies
E1353 Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture
Other Standard
StandardfortheFlamma
Index Terms
bed flammability; cigarette; fire; furniture flammability; ignition; ignition propensity; Bed flammability; Cigarettes; Filter paper; Flammability--building materials; Flammability--textile fabrics/fibers; Ignition--consumer materials/applications;
ASTM E2187卷煙點燃強度測量的標準試驗方法
The most common initiating event in a fatal fire is the dropping of a cigarette onto a bed or piece of upholstered furniture, causing 20 % of the estimated U.S. fire deaths from 1992–1996 in residential structures, according to statistics provided by the U.S. Consumer Product Safety Commission. Test Methods E1352 and E1353 have been developed to evaluate the susceptibility of upholstered furniture mock-ups and components to ignition by cigarettes. Federal Standard 16 CFR Part 1632, Standard for the Flammability of Mattresses and Mattress Pads, was promulgated to reduce the likelihood that mattresses and mattress pads would ignite from a lighted cigarette.
This test method enables comparison of the relative ignition strength of different cigarette designs.
In this procedure, the specimens are subjected to a set of laboratory conditions. If different conditions are substituted or the end use conditions are changed, it may not be possible, using this test, to predict quantitative changes in the fire test response characteristics measured. Therefore, the quantitative results are valid only for the fire test exposure conditions described in this procedure.
1. Scope
1.1 This fire-test-response standard provides a standard measure of the capability of a cigarette, positioned on one of three standard substrates, to generate sufficient heat to continue burning and thus potentially cause ignition of bedding or upholstered furniture.
1.2 This method has value as a predictor of the relative propensity of a cigarette to ignite upholstered furnishings.
1.3 This method is applicable to cigarettes that burn along the length of a tobacco column.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.
2. Referenced Documents (purchase separately)
ASTM Standards
E176 Terminology of Fire Standards
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
E1352 Test Method for Cigarette Ignition Resistance of Mock-Up Upholstered Furniture Assemblies
E1353 Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture
Other Standard
StandardfortheFlamma
Index Terms
bed flammability; cigarette; fire; furniture flammability; ignition; ignition propensity; Bed flammability; Cigarettes; Filter paper; Flammability--building materials; Flammability--textile fabrics/fibers; Ignition--consumer materials/applications;
