ASTM E2190 Standard Specification for Insulating Glass Unit Performance and Evaluation
ASTM E2190絕緣玻璃器件性能和評價的標準規范
1. Scope
1.1 This specification covers preassembled permanently sealed insulating glass units with one or two airspaces and preassembled insulating glass units with capillary tubes intentionally left open.
1.2 This specification is applicable only to sealed insulating glass units that are constructed with glass.
1.3 This specification is applicable to both double-glazed and triple-glazed insulating glass units; for triple-glazed insulating glass units where both of the outer lites are glass and inner lite is either glass or a suspended film.
1.4 The qualification of test specimens is based on frost/dew point and on the absence of fog after the specified test durations.
1.5 The qualification of argon gas filled test specimens is based on the qualifications in 1.3 and maintaining the specified argon gas amounts before and after testing to Test Method E2188.
1.6 Qualification under this specification is intended to provide a basis for evaluating the durability of sealed insulating glass units.
1.7 This specification is not applicable to sealed insulating glass units containing a spandrel glass coating due to test method limitations.
1.8 This specification does not cover other physical requirements such as appearance, thermophysical properties, heat and light transmission, and glass displacement.
Note 1—Sealed insulating glass units qualified according to this specification are not necessarily suitable for structurally glazed applications. Factors such as sealant longevity when exposed to long term ultraviolet light and the structural properties of the sealant must be reviewed for these applications. For more information on the requirements for structural sealant glazing applications, refer to Specification C1369, Guide C1249, and Test Method C1265.
1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately)
ASTM Standards
C162 Terminology of Glass and Glass Products
C717 Terminology of Building Seals and Sealants
C1036 Specification for Flat Glass
C1249 Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
C1265 Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
C1369 Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
E546 Test Method for Frost/Dew Point of Sealed Insulating Glass Units
E631 Terminology of Building Constructions
E2188 Test Method for Insulating Glass Unit Performance
E2189 Test Method for Testing Resistance to Fogging in Insulating Glass Units
E2269 Test Method for Determining Argon Concentration in Sealed Insulating Glass Units using Gas Chromatography
E2649 Test Method for Determining Argon Concentration in Sealed Insulating Glass Units Using Spark Emission Spectroscopy
________________________________________
Index Terms
gas concentration; insulating glass units; seal durability; sealed insulating glass units; unit performance and evaluation; Building materials/applications--specifications; Insulating glass (IG); Performance--building materials/applications (specifications); Preassemble peermanently-sealed IGO; Sealed insulating glass units--specifications;
ASTM E2201 Standard Terminology for Coal Combustion Products
ASTM E2201
1. Scope
1.1 This standard defines terms used in the production, management and use of coal combustion products (CCPs). It is intended to promote understanding by providing precise technical definitions of terms used.
1.2 Terms used only within an individual coal combustion product (CCP) standard, and having a meaning unique to that standard, may be defined or explained in the terminology section of that individual standard.
Index Terms
terminology; coal combustion products;
ASTM E2190絕緣玻璃器件性能和評價的標準規范
1. Scope
1.1 This specification covers preassembled permanently sealed insulating glass units with one or two airspaces and preassembled insulating glass units with capillary tubes intentionally left open.
1.2 This specification is applicable only to sealed insulating glass units that are constructed with glass.
1.3 This specification is applicable to both double-glazed and triple-glazed insulating glass units; for triple-glazed insulating glass units where both of the outer lites are glass and inner lite is either glass or a suspended film.
1.4 The qualification of test specimens is based on frost/dew point and on the absence of fog after the specified test durations.
1.5 The qualification of argon gas filled test specimens is based on the qualifications in 1.3 and maintaining the specified argon gas amounts before and after testing to Test Method E2188.
1.6 Qualification under this specification is intended to provide a basis for evaluating the durability of sealed insulating glass units.
1.7 This specification is not applicable to sealed insulating glass units containing a spandrel glass coating due to test method limitations.
1.8 This specification does not cover other physical requirements such as appearance, thermophysical properties, heat and light transmission, and glass displacement.
Note 1—Sealed insulating glass units qualified according to this specification are not necessarily suitable for structurally glazed applications. Factors such as sealant longevity when exposed to long term ultraviolet light and the structural properties of the sealant must be reviewed for these applications. For more information on the requirements for structural sealant glazing applications, refer to Specification C1369, Guide C1249, and Test Method C1265.
1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately)
ASTM Standards
C162 Terminology of Glass and Glass Products
C717 Terminology of Building Seals and Sealants
C1036 Specification for Flat Glass
C1249 Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
C1265 Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
C1369 Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
E546 Test Method for Frost/Dew Point of Sealed Insulating Glass Units
E631 Terminology of Building Constructions
E2188 Test Method for Insulating Glass Unit Performance
E2189 Test Method for Testing Resistance to Fogging in Insulating Glass Units
E2269 Test Method for Determining Argon Concentration in Sealed Insulating Glass Units using Gas Chromatography
E2649 Test Method for Determining Argon Concentration in Sealed Insulating Glass Units Using Spark Emission Spectroscopy
________________________________________
Index Terms
gas concentration; insulating glass units; seal durability; sealed insulating glass units; unit performance and evaluation; Building materials/applications--specifications; Insulating glass (IG); Performance--building materials/applications (specifications); Preassemble peermanently-sealed IGO; Sealed insulating glass units--specifications;
ASTM E2201 Standard Terminology for Coal Combustion Products
ASTM E2201
1. Scope
1.1 This standard defines terms used in the production, management and use of coal combustion products (CCPs). It is intended to promote understanding by providing precise technical definitions of terms used.
1.2 Terms used only within an individual coal combustion product (CCP) standard, and having a meaning unique to that standard, may be defined or explained in the terminology section of that individual standard.
Index Terms
terminology; coal combustion products;
