ASTM D696 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer

ASTM D696使用石英玻璃熱膨脹儀測定-30℃和30℃范圍內的塑料線性熱膨脹系數的標準試驗方法

適用范圍

Scope：

This test method covers determination of the coefficient of linear thermal expansion for plastic materials having coefficients of expansion greater than 1 µm ⁄(m.°C) by use of a vitreous silica dilatometer. At the test temperatures and under the stresses imposed, the plastic materials shall have a negligible creep or elastic strain rate or both, insofar as these properties would significantly affect the accuracy of the measurements.

引用文件

ASTM D618 Practice for Conditioning Plastics for Testing

ASTM D883 Terminology Relating to Plastics

ASTM D4065 Practice for Plastics: Dynamic Mechanical Proper- ties: Determination and Report of Procedures

ASTM E228 Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer

ASTM E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

ASTM E831 Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis

相關標準

ISO 11359-2塑料 熱力學分析(TMA) 第2部分:線性熱膨脹系數和玻璃化轉變溫度的測定/Plastics - Thermomechanical analysis (TMA) - Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature

GB/T 36800.2塑料熱機械分析法(TMA) 第2部分:線性熱膨脹系數和玻璃化轉變溫度的測定/Plastics-Thermomechanical analysis( TMA)一Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature

ASTM E831通過熱機械分析對固體材料線性熱膨脹的標準試驗方法/Standard Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis

GB-T 2572纖維增強塑料平均線膨脹系數試驗方法/Fiber-reiforced plastics composites-Determination for mean coefficient of linear expansion

IPC TM-650 2.4.24玻璃轉變溫度及由TMA的Z軸熱膨脹系數/Glass Transition Temperature and Z-Axis Thermal Expansion by TMA

GB T 4722印制電路用剛性覆銅箔層壓板試驗方法/Test methods for rigid copper clad laminates for printed circuits board

GB T 4722

ASTM D696使用石英玻璃熱膨脹儀測定-30℃和30℃范圍內的塑料線性熱膨脹系數的標準試驗方法/Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer

GB/T 1036塑料 -30℃～30℃線膨脹系數的測定 石英膨脹計法/Test method for coefficient of linear thermal expansion of plastics between -30℃ and 30℃ with a vitreous silica dilatometer